Carver Owners Forum

Hi I dropping my shafts to do cutluss bearings and looking for spare and replacement Nylok nut for 1 3/4” shaft attached to coupler. I believable it looks like it is brass material but I cannot find the exact Nylok Nut. I have searched the web and cant find anything can anybody HELP PLEASE! Thank you!!

Took the last season off with the Carver to finish up my Shamrock. This morning,my Carver went in for this season. Engines fired right up and I ran her down to my dock. It felt weird after running a single engine boat for a while. Definitely easier with twins.

Hello,

I have two cruise air systems and both seem to be loosing coolant.
I think the leak may be out of the pressure fittings.

I have seen a product that claims to be some sort of "stop leak" fluid. and another product to locate or "smell" for leaks.
I am thinking of soldering or fixing the leaks and then re charging the system.
R22? and some gauges.

Any advise on how to go about this?

Thanks.

And on Cape Cod gas is getting very real.

40ED3FDA-F5E4-416B-88FB-2D30934787E9.jpeg

E791CB84-4C3E-4E1C-AD6E-11CA1BBBC936.jpeg

2577A2F2-F996-4F3A-9E64-32E467625575.jpeg

Anyone ever replace just the fuse holder on a 2896 mariner electrical panel? I want to replace a few that are very difficult to open and close. Also, does the original manual have all the fuse amp recommendations so I can buy some replacements without fighting with each fuse holder? Thanks.

It would sound so simple, but running out of luck. I am in need to preface the masthead light on my newly acquired 355 Aft Cabin. The previous owner installed a 48" pole with a 360 light that makes zero sense as its not the highest point on the vessel and now just in my face. Also bent and loose. I want to replace it with something low profile and 225 degrees viewing. I can find lights like the AquaSignal series 25 replacement light, but not the bracket to place it in the desired location (or at all for that matter) . Does anyone here know where I can source something like what should have been equipped originally?

Hello,everyone, I am new here and recently bought a 2003 carver 350 mariner, may I have two questions:
1. How deep can the anchor goes?
2. Should I pump out the waste? How do I know when I should do this?
Thanks!

I have a 2006 56 voyager .Need to find the location of dimer control for vip. I have found the other 7 dimer. This one has me puzzled. Any help would be great.

Southwind.

We have a 3607 aft cabin with the sliding hatch and short doors. Last year I tried a number of options to try to keep the bugs out. Different types of screening. Some draped over the door. One attempt at hanging something from the railing around the door. All of them were very awkward to use. What do others use? I like to keep the doors open for the breeze and ease of use.

We are purchasing a 1989 3607 Carver aft cabin. We haven't owned anything bigger than a pontoon, so are a bit intimidated with such a big boat. We plan to drive it on Lake Michigan from Benton Harbor to Muskegon Lake in a few weeks. Any tips would be appreciated!!!

Thanks,
David and Brenda
1989 Carver 3607 aft cabin

Welcome to Carver Yachts Owners Forum

View the latest post Attachment(s) Nyok Nut on 1 3/4” shaft coupler need replacements

View the latest post Attachment(s) Splash 2022

View the latest post Attachment(s) Repair and Charge Cruise Air

View the latest post Attachment(s) Boat gas getting real.

View the latest post Fuse holder replacement

View the latest post Attachment(s) 355 aft Masthead Light

View the latest post Carver 350 mariner

View the latest post Attachment(s) Dimer Control

View the latest post screen door

View the latest post New owners