Curious if any of you have any knowledge of an old (~73?) Wankel engine that was used for small boats. This is NOT an outboard, but a single rotor engine with a lower unit to drive a prop. This does not pivot, so it still needs a rudder, and I don't believe there's a transmission, so once the engine is running you're in fwd gear (like the old PWCs!)

I just picked this up as a project. Thought it might just be a "show" piece for the garage, but I believe it's complete enough to get running. ...

I am going to fit a crane (Davit) to my 450 Voyager as it has not had the factory one fitted. Does anyone know if the pole passes right through the top deck down to the salon floor or is it only terminated at the fly bridge floor under the seats. I assume they set up all the hulls to take a crane if ordered. Thanks

Hey All;

Ok, so my 396 was getting tucked away for a nice winters slumber when one of the deck hands jammed the side door closed without lifting the "plunger latch" on the side door. when pushing it back, the bottom plunger that goes into the hole broke off.

Trying to research the part and mechanism to fix it, but seem to be striking out. does anyone have any idea where I can find the parts manual for the door?

Thanks all!

Hello everyone! I am new to the forum but not to boating. I have recently moved onto my Mariner 32 and I am enjoying every minute if it. I am looking forward to picking your brains and getting your input on things when issues pop up. Thank you in advance.

Found this video which really shows what is going on. Does last for 13 mins but well worth the watch. Definitely an eye opener to say the least. https://www.youtube.com/watch?v=UvS_D4_lF5U

Must have been a raging storm on the Eastern shore of Lake Huron. There are bits of dock, trees, surf boards you name it - any manner of flotsam imaginable has washed up.

The once sandy beach is all stones and large ones at that. The dunes and seagrass are washed to the treeline. My muskoka chairs are one with the universe now.

In all the chaos I found this thing though. Looks like it could be a boating thing but hard to tell. No markings that I can find.

I am impressed with how robust t ...

Hi folks,

I have. 97 Carver 405 that rides low in the bow. It plows. I have tried various rpm’s, from 1200 to 2000, and I’m told the bow is way down. The spray is nearly up to the gunnels. I,ve also been having issues with water coming into the fwd bilge. Over 6 gallons during a 6-7 hr cruise. Related? I did discover a leak in the fwd A/C condensate line to the shower sump. Hopefully I fixed that. We’ll see tomorrow.

We checked the trim tabs and have them turned up as high as they will go. I’ll ...

Hello all,
Just picked up my Santa Cruz Carver today. 28’ long, 10’ beam, 7.3 Diesel engine, single screw. Boat is mechanically sound and needs some cosmetic work. Other than that, it’s just some touching up. Any recommendations that I should work on first? Also, where is the best site to purchase items or accessories specific for Carver rather than “universal”?

Hello All,
I am preparing to change all the hoses to the aft waste system in my 2004 396. Two of the long hoses in the system (toilet to vacuum pump, and pumpout line) connect to PVC pipes way down in the bilge. About the only way I can see to access those fittings is to remove the port muffler. Anyone have any tricks or suggestions to avoid that big job? If I remove the cabinet next to the bed, would that give me some access?
Thanks for any suggestions.
Thatchh

Hello looking for some help! I’m looking for the window seal for my 1992 330 aft cabin. It’s the aft cabin escape window, it was manufactured by Taylor. I have contacted carver and Taylor no luck with them. I would like to get a replacement seal if possible or a replacement window the dimensions are 271/2 wide by 161/2 tall that is the outside dimensions. I have added some photos for a better understanding of what I need. ...