Engines 2001 mx6.2 merc mpi......I would like to use this thread for this type of discussion for anyone.....In a short while, hopefully, I will be getting the boat ready and want to go thru each engine and check harness plugs,grounds etc because at the end of the year the port engine would try to stall the odd time when you pulled the throttle back quick..otherwise ran like a champ, great fuel mileage etc.......I will clean the plate on the Tb, lube the linkage, and check the iac filter etc....have new iac's and tps for both....there does not appear to be any codes as there is only one beep when ignition turned on. I will get tech to check for codes after all that. So I guess the question....what is in charge of controlling the fuel when you pull the throttle back to idle quickly.?????thanks guys......

I just bought a 2005 Carver 396 Motor Yacht. When we pulled it out for the survey, I found both trim tabs to have a metal brace on them as shown in the picture. No one in the yard knew why they were there.
Does anyone have any experience with these braces? They do not slide, but at bolted tight.

Hi All, curious to see how folks are securing kayaks/ stand up paddle boards to their front railings? We have a 29' Monterey if it matters.

I found this online:



seems pretty pricey for rolled pieces of metal covered in foam with mounting brackets. Has anyone rigged up something similar or know of different options?

I just purchased 1988 32' carver aft cabin and the hatch over the v berth is leaking and has been calked a few times . I want to replace . Where is the best place to find a new replacement ?

Thank you

I'm new to this forum so I'm not show if this is the correct place for this. I have a 1986 Carver 3207 and was wondering if anyone knew where to get an owners manual for this generator. It is the original generator. Thank you for the help.

We have not been able to find anyone to fix our refrigerator and Marvel has said they have been discontinued. Has anyone found a replacement for the this refrigerator? It is a stacked freezer/refrigerator unit, and the freezer runs great! This is in our 2001 - 506 aft cabin.

Aquayacht Harbor's tech worked on it and refilled with whatever type freon they use now, which lasted a few days, and he could not find the leak. I understand that if there is any moisture introduced it can destroy the heat exchange and compressor. So I think we need to replace.

I just purchased 1988 32' Carver aft cabin and has all original electronics, screens do not have a display any mor on depth finder the navigation is all lat an long. any recommendations on navigation gps and depth finders? I know we can download a lot of charts on tablets now but any thoughts would help.?!

Hi,

My starboard transmission on my 405 is noisy. After reading all of the great posts here, I decided to start with the engine and make sure it is running right before proceeding further aft. I replaced the cap and rotar and the replaced the plugs. I made little wooden rack so I could put the removed plugs in the correct sequence for inspection. After removing them I found a website that offered pictures of spark plugs in various conditions. (after removal). Obviously from comparing mine to the pictures, all are showing rich. They are basically black and smell like fuel.

Now, what might be the cause of black smelly plugs? I have read that things like fuel injectors, throttle body, wrong plugs, wrong gap......and various other things. We have owned the boat for about six months and are fixing things one at a time.

The engine runs and idles OK, although our marina mechanic says he can feel it vibrating when he puts his hands on the risers.

All ideas are welcome....thanks

My Carver 444 Cummins 370 port engine is spooling up slower than Starboard engine after reaching 2000 rpms. The port engine start coming up to full rpm after approx a minute or so as the boat begins to plane. I recently had shafts and castle bearings replaced but suspect turbo charger. Any thoughts?

I am looking for the switch plates on a 3607 helm.

They are the ones with lights, fuel, voltage etc.

They are about 3 x 6 made from aluminum, I think.

I've been looking for about 4 years with absolutely no luck.

Hopefully someone here has a set sitting around, or can direct me to where I might find them.

You can see them here in this picture.......not mine but similar.