Does anyone know if Carver still supplies sun pads for the fore deck of the 405? I tried asking through their site, but the messages don't seem to go through. I have snap's on the deck from the previous owner but no pads. Carver listed the part number as #A0017115. My concern is to have any new pad made to fit the existing snap configuration. If Carver no longer supplies the item, any recommendations are welcomed for a supplier. I have a shop in NJ that reconditioned my isinglass and canvas', did a good job so I may check with them if no luck. Thanks

Trying to figure out what pump 1, Pump 2 and tank 1 are. I'm fixing a carver yacht that took on water and trying to get the bathrooms online. If anyone has a water pump diagram of a 2 bathroom 40-60 carver that would be awesome. I noticed I had two different water tanks one for each bathroom I really would like to take a shower one day any help would be great. Does anyone know what the pumps look like that provide the pressure to the showers and sink? Thanks

Swim platform on my 1987 280 Voyager was squishy, so I replaced it. It turned out amazing.
Used swimplatforms.com.

If anybody is ever in Saint Joseph looking for a slip to use, I'll offer free use of one my slips for a few days. Two in southwest Michigan, 10 minute idle out to the lake, and one in southeast Michigan, in Trenton, between the two Grosse Ile bridges.

One is a 45' long x 25' wide at St. Joe Isle Yacht Club and another is one of two 40' x 20' right in front of my condo. Am in walking distance, if you don't mind a short hike, to downtown St Joe. We regularly walk here, unless it is really hot or muggy out.

I think I have the slip in Trenton rented out - 40x 16, but if not, if you need a place to stay for a couple nights, just drop me a line.

30 amp 120 electric, at all 3.

Only offering this to CarverYachtOwners.com active registers users.

Hello all. I just came across this forum while reading anything boat related online, as I cannot wait for spring here in Chicago. I guess looking at pics of boats in the water online helps get me through the 10 degree days we are having here. Ha. This is our first boat owned (wife and I). We bought it last September. Pretty much just in time to drive it to the Marina for winter storage. So we are eagerly awaiting this upcoming season. I look look forward to being a member here. Seems like a great source of info and camaraderie. If anyone is on the Chicago lakefront, drop me a note.

I have a 2001 carver 466 with an twindisc ec150, fly by wire type control system. I'm looking for a used ec 150 throttle/shifter unit to install on my aft deck for backing into my slip. Vision from flybridge is terrible looking backwards. Have image if someone can help me upload it. Don't see how to add it here. I have searched online and can't seem to find one anywhere, not even a picture of mine! Hopefully someone knows where there could be one. It has a selector switch on it to tell system which station you are at and a three position throttle preset. Thanks

the duct on the vent in the salon that runs off the aft cabin unit has broke off has anyone had this problem and figured out how to run a new duct

Hi, just purchased a 1993 Carver 370 aft cabin back in August. Any suggestions on how to order parts for it? I notice that they are hard to come by

Can anyone help with how to remove the salon widows from a 1993 carver 350 Motoryacht

Hello,

Just became a member and looking for answers already! Recently bought the Carver and I am lacking any real electrical drawings. Problem being faced is this;

When power is applied to console and fuel level is sought by switch, either Port or Starboard:
A) Lights come on the fuel indicator gage
B) No needle is ever show
C) 5 gallons of fuel has already been placed in each tank

Since I see no change when calling either tank, it appears either an open wire or bad gage. But I would love to find some wiring diagrams before 'diving' in.

Thanks