Good morning,
I am new to this forum having just purchased my 2014 C40 a few months ago.
I am upgrading electronics and need a new helm dash panel for the fly bridge dash.

I have tried looking for parts catalog without success. Can anyone steer me in the direction of a new ( or used ) dash panel?

I am installing 2 12” chart plotters side by side

Thank you in advance

This news really sucks. I figured I would go to the boat to start some prep work if things get slow at work. got this email a few minutes ago.

Crysler Park Marina’s priority is to protect the health, safety, and well-being of our customers and staff in these challenging times.

The Marina is currently closed for the season and gate locks and codes have been changed. There will be no access to your vessel and/or equipment from March 18 to April 6. Please ensure that your service providers are awar

...

Looking for a replacement latch for the swim platform dock box. Probably the same for 355/356 and 405/406.
Thanks

Hello everyone, I'm new here as I don't have a Carver... yet.



I'm looking at a very nice 1997 Santego. I'm looking for any advice for things to look for. Of course a survey will be done, but I'd like to check out as much as possible on my own first. I'm mechanically inclined and have been boating for 10 years, mostly with sub 30' express cruisers with stern drives,so happy to accept any recommendations on focus areas.



The boat I'm looking at has about 650 hours on the 7.4 Crusaders. There is ...

Hey guys & gals. I am Robb. I have just purchased a 1986 Montego 26, salvage boat. It has been sitting in a yard for 10 years. I am really excited to be fixing it up and motor-boating down the ICW. I just got one snag. Can anybody send me a pic of the transom drain plug, so i can find its location? The manual says its in the engine department but shows no location. It looks like the bottom of boat show towards right of engine. My engine compartment has water covering it up. Thx for the futur ...

I am going through a new to us 1989 3607. I've got some engine gauges on the upper helm that either don't work, or only work when they feel like it. (Crusader 350hp/454's) What is the easiest way to get to the back of the gauges on the uppper helm? Looked at either take out all the switch panels, or take out the foot rest well.

Any help would be greatly appreciated.

Thanks,
Winegrapewill

Looking for the latch for the starboard wing door on a 1999 356 Aft Cabin.

1990 Carver 3607 Aft Cabin

Asking price: $45,000



● Twin Mercruiser 454s

● Port Engine hours: 1358

● Starboard Engine hours: 1361

● Onan 9kW Genset

● Fuel: Gas

● Two fuel tanks: 125gal each. 250gal total

● Two self leveling fresh water tanks: 98gal total

● Three Marine Air heating and cooling units with individual controls (raw water cooled)

● Three births (V-berth, dinette, and aft state room)

● Two electric macerating heads

● Large shower/tub combo in state room

● Separate shower sump pumps

● Two waste tanks ...

I just took out my Marvel (OEM) factory installed 24" fridge and freezer unit out of my 01 466 and replaced with new Stainless Marvel units, Both units work great and get ice cold. We just updated the galley with all new Stainless appliances so the wood laminate door look had to go. $500.00 for both units. Any questions call my cell 708-610-8365

Good Morning, Everyone.

My wife and I are moving up to a 1992 33' Aft Cabin from our Sea Ray 280SD. Well, we are still in process - subject to survey and sea trial, which will be in a month or so.

Any advice on Carvers in general, or this model in particular, would be very welcome indeed! Any issues with the 454 Crusaders (approx 1000 hrs)?

A big step up for us in length, beam, and weight (and comfort), but we're very excited!

Cheers!