We have black granite and and experience lots of fingerprints. Not sure what type of coating may have been applied. Currently, use a windex-type product to clean. Have previously used a stone and granite cleaner which made it worse. Anyone else having the same issues? Looking for cleaner suggestions.
Thanks in advance.

I'm looking g to remove the Seakey from my 2003 boat. Has anyone done this? What all is it wired too?

Thanks

Sometimes pedestal water has some funny plastic taste to it, although I have a filtration system on board no harm in putting in better stuff when filling/using water from the source. Came across this which is similar to the RV stuff and thought it might interest others. Going to buy a 2 pack, one for the permanent pedestal hose and another for my travel hose. Chuck them after the season is over. Same product is available on Amazon US by the way.

https://www.amazon.ca/AmazonBasics-Inli ... merReviewsSometimes pedestal water has some funny plastic taste to it, although I have a filtration system on board no harm in putting in better stuff when filling/using water from the source. Came across this which is similar to the RV stuff and thought it might interest others. Going to buy a 2 pack, one for the permanent pedestal hose and another for my travel hose. Chuck them after the season is over. Same product is available on Amazon US by the way.

...

We are in the process or installing "dual" marine Puck Isolation transformers behind the main salon TV/Power cabinet, replacing our "factory installed" ProMarine Zinc saver.\

https://www.bridgeportmagnetics.com/bmg ... nsformers/

Marine-Pucks are toroidal (ring shaped) isolation transformers fully embedded in solid epoxy resin inside a cup-shaped non-metallic enclosure. They are sealed hermetically and can be mounted onto a deck or a bulkhead.

There are many advantages of to ...

Is the primay supply to the ref from the 12v or 110v when both are on? I have been told not to leave the 12v breaker on when at dock with shore power on or when the gen is running because the 12v is the primary and the ref is running off the battery.
Thanks for your help

How do I get the bilge pumps to run all the time and not automatically ? there are switches in aft closet,on both the fly and lower helms and on the main pannel. I want to run the mid pump to remove some water but it seems to be set to come on only for short moments.Thanks for your help.

As we all know winterizing the AC can be a B. I usually do it in the water so I can activate the AC pump as on shore I have no access power.

AC pumps are not self priming and therefor you can blow or run fluid past the gears/vanes without any pressure. I just bought one of these https://www.amazon.ca/dp/B07DM3SJPT/ref=dp_cerb_1 Which I will insert into a 2 1/2g wide mouth pink stuff container. The other end gets connected to my strainer cap adapter. It comes with long leads and a switch on the le ...

Well, I finally tired of looking at my circuit breaker panel and seeing all of the panel indicators not working. So after locating a spec sheet for Solico (Sorenson Lighted Controls) I determined what I needed and what I wanted. The original panel lights for the DC side were part # 1835-1-10-20140 or 18 series 14volt incandescent -6' wire leads - white base with no finished bezel - flush translucent green lens and the AC side were 1850-1-10-20140, same as above but 125 volt neon. Here is one o ...

Hi,
Greetings from St. Louis, Missouri. I am proud new owner 1987 Carver 4227. My understanding that there were only 13 made! It's sister-model 4207 is more common I hear. The boat is a bit of work and I am sure I will be asking questions on this forum soon...

Cheers,
Pekka

1994 320 Voyager owner. Chipped my swim platform about the size of a silver dollar. Would like to repair before winter. Local repair shop has recommended patch Paste by Spectrum. Does anyone have experience with this product and if so what color should i use to match my boat. I am a new Carver owner and monitor this website constantly for insights. Thanks.