I have two multifunction Displays that I am selling for a couple of friends that recently upgraded their electronics.



The first one is a Raymarine C80 Classic. It comes with the Navionics CF card, sun cover, power cable, document binder and manuals.



The second one is a Garmin GPSMaps 5280 which also comes with chart card, software update card, sun cover, power cable, and documentation.



Both units were flush mounted, so we don't have the optional trunnion mounts. Both unit were working and in good ...

Looking to update the software on my C120 Classic MFD. Followed the instructions from the Raymarine website. Downloaded the update and transferred to the compact flash (128 MB).

The download produced v5 folder. Contained within this folder were 2 items: AUTORUN.DOB and C_App_Prod516.pkg (this is what I copied to the compact flash drive)

I removed the Navionics card and inserted the update into the MFD and turned the unit on and nothing happened. Did I miss something in the instructions? Raymarine ...

Hello Folks,



After a month and a half of dry-storage for a full bottom job, some fiberglass repair, wax, buff, etc got the boat on the water. This Boat is new to me, and fuel tanks were empty/filled with watery gas when I got it, so I had them pumped. Fresh 20 ga each tank I took off for fuel station and starboard engine died after about 1.5 miles. I figured either gas evaporated or tanks are too big for 20 ga (4 of 5-Gal red pales each). Another possibility is that guy pouring in gas miscounted ...

My AC unit in the aft cabin (3 knob control) cycles when the fan is turned on. When I switch on the compressor, it too cycles however it does not produce cold air. The water pump is circulating and water is flowing out the outport. Either the refrigerant is low or the compressor is not functioning properly. If it's a matter of replacing the compressor, where can I find a new or used one? The unit is a Marine Air VR6K-H. Or is the last option to replace the entire unit with a new model more cost ...

Good day all!! New to this forum and recently purchased a '89 Carver 3607 Aft Cabin. Looking forward to reading some of the many tips you have to share.

On my 2001, 356, I have an automatic genset/shore power transfer switch that I'm pretty sure is located behind my 120v breaker panel. My boat will not power up electrically using shore power, but will running the genset. I'm almost certain the transfer switch is stuck in the genset position and will not switch over. In the morning I'm going to open up the panel to see if I can find the problem.

Could this be as simple as hitting it with a shot of WD-40 or is it more complicated? I've never op ...

I have a 2000 356 need to replace carpet inside boat any suggestions ? I have been looking for marine carpet people to replace it but no luck so far. Should i hire a house carpet person ? The marine carpets that I have found are all snap in rubbber backed cheap looking carpet. I would like a nice plush carpet. Any help is appreciated

Hi,

I'm looking to replace the house batteries in our newly purchased 2002 396. Has anyone installed Golf-Cart batteries in the stock location? If so do you know what series of batteries that fit. I'd measure but the boat is currently 800 miles away and waiting to be transported to Southern Ca.

I would also like to know what series the stock batteries are if anyone has info.

Any help is appreciated

I've been poking around on the forum for a few month's while searching the south-west for a Carver. We are now proud owners of a 2002 396. The boat we purchased is very clean and mechanically well taken care of. It does need a little polishing, Isinglass replaced and fresh batteries. I'm going to be asking for input on house batteries. We will be moving it to Southern CA. soon.

Here's a couple Pictures

I have a 18" x 36" spongy area on the bow of my 36 Mariner. It has been that way for 10 years and has not changed but it is the only flaw on our boat.It is not structural but thinking about fixing the problem. What are my options in fixing this.can it be done from inside the boat or filled. Looking for anyone that has had this kind of issue. Thanks for the help.
Tom P.